2012년 6월 12일 화요일

2nd laminating

We did the 2nd laminating, two of us worked on making splashes.

Chris explained us about how the splashes stand up, centre board is pulled up, mast goes on top but actually I couldn't follow what it means exactly. We will see it anyway.

Andrew is drawing another line for the thickness of the mat on the plywood. I couldn't get the exact concept this morning. Maybe I wasn't awake.


Dryfitting


The splash goes on hull and support like this anyway.


Those tanning lines are rebates for the laps. Make sure not forget the little part each side of chine which can't be easily sanded. Tapu and I got a mission of that last laminating at nose tomorrow.


Andrew interpolated a line between two frames, which seemed to be pretty precise.


Drew two lines of frame, mark some points between those lines, use a batten and draw the line.

This material is the one that has to be done by vacuming. Nomex homeycomb.


Get ready to vacume.

We apparently put more glue this time so that those dots of resin stretches to where the hose vacuming is.

nomex & kevlar
duritec
hibuild
A/B/C/... class cat
buff up
genoa
gennaker
spinnaker
jib
amber



2012년 6월 11일 월요일

We laminated the first section of hull outside.


I checked the boat of what has done last wednesday afternoon. Coved on the chine, filled all gaps, put the chain plate into the situ, rebated the laps of EDB.


That edge around the tube will be coved one more time after chopping that bit off to make the tube flush to the nose cone. We are going to laminate the very forward part at 3rd which is the last and it could be next monday.


Tha forward gaps between those plankings are filled up.


I think Chris put this tape to make sure to hold that chain plate there. We rebated 75mm wider part around that chain plate for 1. reinforcing, 2. dispating shock waves and load.


That is the lap being rebated.


A bit of lumps and hollows at the edge of centre case is filled up as well.


This is the resin that we used today as a sealer coat.


This is the hardener. The mixing ratio is 1:1.


Moving the boat into this room, we closed the big door of the FRP bay and did jobs. We turned the heater on but it didn't work at first.


We coated a bit on the bottom of the hull at the bow. We poured almost 3 L of sealer coat on the hull totally.


We put a piece of peel ply to prevent vac tape stucking on the foam and the planking. The sealer coat worked on the timber but I don't really think that it worked on the foam, we have got almost a full bar in the end anyway though. Sealer coat is supposed to be used on special surface like timber. Chris doesn't like the slurry spreading on the glass as well.


Jun is putting sealer coat.


Lance got in the cabin top to do some jobs such as sanding the cove and tape on it, so that vacume hose was needed to let in. He found that the cove wasn't quite good enough, which I agree with, so probably need to cove one more time.


Tapu is filling the gap between hull ant deck, laying on the floor.


We need to block that centre case plug made of 3 pieces of MDF somehow because it has not been laminated or sealed with each other. We put some bleeder on top of it to protect the bag from the sharp edge, putting vac tape around the bottom of it and covering the vacume bag.


I think we used this powder when we filled the gap.


A small piece of EDB went onto there. Make sure that piece isn't bigger than the rebate. We actually had to cover that on the deck by75mm but the laminate on the deck is done and we can't rebate on the laminated surface. We leave the whole layer of laminating as possible as we can.


Started.


On going.


A nice looking dinghy! I like the pads on the bottom.


We blocked the stanchion like this with peelply and bleeder covered on it.


Vacuum bag is hardly ever big enough. I cut that 1m longer and wider but it just fitted.


We have almost got a full bar eventually.

convection






2012년 6월 6일 수요일

Planing and sanding again

We carried on planing and sanding today.


Chris has a tool for gripping the plane blade when honing, which was pretty comfortable.


Cut off that extra part plum to the edge of nosecone. That extended part of nose cone is going to be cut off plum as well.


Nice cut but it has slight angle in the picture so we sanded to make that right angle.


Getting neater. We check the fairness by using batten several times.


What has been done this afternoon? I left earlier today because I had something to do.


Nice. We will cove that edge around the tube.


Lance grabbed a strip of yellow cedar as a batten somewhere and check how fair it is, which is good.


We routerd the foam out where the chain plate fit into. We can see the floor, flange and the coving through the fibreglass.

Probably, fairing is done this afternoon and vacuum, dryfit EDB, rebate the lap, glue chain plate and fill the hollow part at bow with glue, sealer coat. I'm wondering that if it is good to laminate on wet sealer coat or dry.



2012년 6월 4일 월요일

Planing and sanding

It was Queen's birthday yesterday. We did sanding and planing today.

Chris told us to think about what we are going to do today, especially about the chain plate. It has long edge above as a trapezoid and goes into where we dig the foam out by its shape. We have to sand down by the thickness of one layer of fibreglass, where is going to be 75mm bigger surface of the plate. We are going to laminate on the whole surface of hull afterwards.


Put the longboard as pararel to longitudinal direction as we can and sand it roundly.


This is a list to do. Chris emphasized we have to do sealer coat before laminating, especially the end grain on the transom. The last stage goes a bit lazier than I thought. We will vacume next monday.


Lance brought a plug for mould for his remote controlling trimaran model, which is made of epoxy and MDF.

Planing and Sanding.


Looking back, Chris told that he would have put extra frame to get the strip plank tip been pushed down forward side. It is not quite enough to twist them by the frames we had.


Taken from upstairs, it appears a bit wider than I supposed.


We have to be aware of not doing planing and sanding at the same time. The main reason of blunting the plane blade is not epoxy or wood but the sand from longboard. Planing is much quicker, cleaner and easier.


Chris told that part is going to be capped later on. We have to make chine round only after we get the fair shape or line.


Lance is doing his job at smoko.


Someone drew a portrait of Chris on the protector of the grinder. It must have been Ogi!!


We took the measurement and location from AutoCAD and transfered by using centre line, right angled line and plum-bob. Andrew made that pattern as well.


We need sanding.